Body Dryer

Description

My Body Dryer is a 13×7×0.50 square shape apparatus. All parts and components of this drying device are the same as a hand dryer except for the flexible hose that is attached to the duct. This body dryer is a complete drying device because of the flexible hose; which allows any user to completely dry from head to toe. The flexible hose will be utilized as the cloth towel. This hose expands to 6-10 feet. The body dryer has a powerful motor that blows warm or cool air. These features allow the user a direct point of contact at will and the hose is hand held and self-directed to all areas of the body to be dried. The air from the hose will blow all the water from the body and thus drying the skin to the end user desired dryness. For best results: One should start blowing the water beads from the entire body from head to toe or vice versa; this should take about 35-40 seconds. After beads are blown off, you are now drying your body as you move the hose about and around your body structure. If you are drying off after 3 minutes, it is because you are caught up in the feel good sensation.

Body is dry and no damp towel to wash, dry nor fold. The only thing that needs to be hung up is the hose nozzle inside the magnet housing cover base. Drying off have evolved to the next level. The flexible hose is a medium firm plastic that will enable the user to maneuver around the body. The hose for both models (Standard and Pro) is designed to be 6 ft (when the nozzle is clipped magnetically to the housing the hose drops down 3 ft. and back up 3 ft.) that's when expanded expands to 10′ safely. Both units are designed to be mounted on the wall. The wall mount is designed in such a way that with a click of a button and upward pressure the unit gets released from the wall.

Standard Model:

• • Voltage 110V/60 Hz, 1800 W
  • Max. Air Temperature: 50 Degrees Centigrade—122 degrees Fahrenheit
  • Air Speed—26 M/S
  • Airflow—270
  • Protection level—1PX1
  • Electrical Isolation—Class 1
  • Finish—White molded plastic case
  • Motor—brush Motor, 75000 RPM

Pro Model:

• • Voltage 110V /60 Hz, 1800W
  • Max. Air Temperature: 50 Degrees Centigrade—122 degrees Fahrenheit
  • Maximum Air Speed—60 M/S
  • Air Flow 200 M3H
  • Drying time to any one area—8 to 10 seconds
  • Protection level—1PX1
  • Electrical Isolation—Class 1
  • Finish—White molded plastic case
  • Noise level at 6 ft distance—70 bd
  • Motor—brush motor 25000 RPM
    Controls: Push Button On and Off Switches and Shut-Off switch in Nozzle when in the cover shuts off Fan and Heater.
  • Fan Speed: Off, 1, 2, 3 (or more if desired)
  • Heater: Off, 1, 2, 3, (or more if desired)
• 1. Remove Nozzle from cover.
• 2. Press the “ON” button and dry hair or body.
• 3. After 5 minutes (this could be any amount of time) the unit shuts off automatically. If still needed, just press the “ON” button again.
• 4. Unit can be shut off at any time by either pressing the “Off” button or by replacing nozzle into its receptacle in the cover.
• 5. The control circuit should not allow the Heat setting to be higher than the Fan setting, as this could overheat the components. However, the fan can run at any setting as long as it equal or less than the heat setting.

BRIEF DESCRIPTION OF DRAWINGS

FIG. 1A: Body Dryer base assembly cover shows front facing with flexible hose extending from the duct and hose nozzle attached inside cover base nozzle station.

FIG. 1B: Shows the same as 1A, except the air vent holes from the bottom view.

FIG. 1C: is a clear view of the bottom base which depicts the hose position and air vent holes.

FIG. 1D: is a right side picture of the base assembly as it lay flat on back side with flexible hole attached in duct and nozzle resting in station.

Replacement Drawings contains No New Matters